Do Snipers Clean The Bore Of Their Gun

in: Featured, Gear, Lifestyle

• Baronial 19, 2008 • Last updated: September 26, 2022

The Basics of Cleaning Your Revolver

Several years ago my dad gave me my first handgun- a Smith & Wesson .357 magnum revolver. It didn't come as a surprise. I had grown upward around guns and had hoped that one 24-hour interval my dad would pass a few on to me. Because of the value of this gift, both sentimental and budgetary, I felt a existent responsibility to accept intendance of information technology so that it would last for many years to come. I learned how to make clean it well and have washed so ever since.

Any gun possessor knows that properly cleaning and maintaining your equipment is not only key in increasing a weapon'south lifespan, but is necessary to ensure safe operation. Simply similar shining your shoes there are every bit many ways to clean a gun as there are stars in the sky. The following is a guide to cleaning a standard revolver.

*Quick disclaimer: I am only a gun possessor, not an expert or instructor. Read your gun'southward owner'due south transmission for specific cleaning instructions and if in dubiousness, consult a certified artillery dealer. And ALWAYS Make SURE YOUR GUN ISN'T LOADED BEFORE CLEANING.

Watch the Video

Cleaning a Revolver:

Step 1: Brand certain your gun is not loaded.

Stride 2: Go your cleaning supplies together in the aforementioned place. Below is a typical universal gun cleaning kit that you can buy at about outdoor stores OR hither for effectually $fifty. Besides this, you need some gun cleaning solvent and gun oil. There are many different kinds and most work for all types of guns. Here I am using Hoppe'south No. ix Solvent and Remington Oil.

Step 3: Tie an old sock or rag around the rear cylinder opening. This will protect the revolver from damage when the diameter brush gets pushed through the butt.

Pace 4: Dip your bore castor in the cleaning solvent. In that location are different sizes of bore brush that correspond with the barrel size, and then brand sure you lot match the size accordingly. It should be imprinted somewhere at the base of the bore brush.

Footstep 5: Feed the bore brush through the butt of the gun. The diameter brush handle will naturally twist in your hand as information technology follows the rifling within the barrel, don't try to finish this. Make certain the bore castor goes all the way through the barrel, exiting at the other end. Then come dorsum through the barrel in the opposite direction.

Step 6: Take a cleaning patch and dip information technology in cleaning solvent then feed it all the manner through the barrel of the gun. There are many different opinions on how many times to do this, but I have always used 1 solvent covered patch followed by 2 dry out cleaning patches. If your butt is peculiarly muddied yous may need to exercise this a few more times.

Step 7: Using a brush (you can utilize a toothbrush if you lot don't accept a cleaning kit), make clean around the muzzle of the gun; then, using a footling cleaning solvent, clean the rear cylinder opening.

Footstep eight: Using the brush again and some cleaning solvent, brush the cylinders, both outside and on the ends.

Pace 9: Continuing on, clean the extractor rod with the brush and solvent. Make clean both the front side then push it out and make clean the star and the rest of the rod normally housed between the cylinders.

Step 10: Using the bore castor and the cleaning solvent, clean each of the cylinders in the same fashion that you cleaned the barrel. Remember to go all the mode through on each side.

Step 11: Use the cleaning patches in the aforementioned manner as you did with the barrel, taking the first patch and dipping it in the cleaning solvent before feeding information technology through an individual cylinder. Clean up by using two make clean patches to get any excess residue.

Step 12: Using a clean cloth, take a minor amount of gun oil and begin covering the gun with the exception of the paw grips, within of the butt and within of the cylinders.

Footstep xiii: Wipe off any excess oil with a different rag then polish up the gun with a silicone gun textile. If information technology looks similar your gun is greasy or oily and then you need to wipe it off some more; it shouldn't look like a fat guy covered in baby oil.

Finally, remember this is only a standard cleaning that should be performed after every time at the range or in the field. If your gun is used heavily, a more thorough dis-assembly and cleaning should exist performed. If you aren't certain how to practice this, contact a qualified gunsmith or expert to assistance yous out. And of class, always make sure to beverage a Hansen'due south Natural Soda while cleaning your gun; it will keep yous sharp.

Picket the Video

Tags: Cocky-Defense & Fighting

Previous Next

Source: https://www.artofmanliness.com/lifestyle/gear/how-to-correctly-clean-gun/

Posted by: brighamficepleturem.blogspot.com

Share this post